Repairs and aftercare · SA12

Safety edge and photocell repairs in Port Talbot

If the electric roller door on your garage in Port Talbot won't close, or reverses for no reason, the safety edge or photocells may be at fault. We repair and replace them for homes in West Glamorgan, with the visit price agreed before we come out.

Request a visit Call 0800 088 6248

Guide price: from £99 inc VAT
First step: Visit price agreed first
Covers: Port Talbot, SA12 and SA13
Area: West Glamorgan

Rubber safety edge on a roller door bottom rail and a photocell sensor on the guide rail

Computer-generated image

What should I know about safety edge and photocell repairs in Port Talbot?

Photocells either side of the opening stop the door closing while anything is breaking the beam between them.
Replacement safety edges and photocell pairs have fitted prices, agreed before the visit is booked.
Never tape over, bridge or bypass a safety device to make an electric roller door close.
After a repair, the door is tested to check it stops or reverses on obstruction before it's handed back.

How does it work in Port Talbot?

Tell us what the roller door at your home in Port Talbot is doing and what you've checked. Photos of the bottom rail, photocells and control box label help.

STEP 01
Tell us about the door
Describe the door and what you need, with a photo or video if you can.
STEP 02
Agree the visit price
We confirm the visit price before anyone comes out.
STEP 03
Visit
The engineer finds the cause and makes the door safe where possible.
STEP 04
Parts quoted first
Any parts are quoted before they are fitted, so you decide.

How much do safety edge and photocell repairs cost in Port Talbot?

Item	Guide price (inc VAT)	Ex VAT
Photocell pair replacement, fitted	£99–£189	£82.50–£157.50 + VAT
Safety edge replacement, fitted	£159–£295	£132.50–£245.83 + VAT

Guide prices for homes, last reviewed 25 October 2026. Your written quote is the price. See the full price list.

Covering Port Talbot and nearby

We take enquiries from across Port Talbot, from SA12 outwards, and confirm every price and date in writing before anything is ordered. For reference, Port Talbot sits roughly 7 miles from Swansea.

Nearby, we also take enquiries from Neath, Maesteg and Swansea.

Rules that apply in Port Talbot

Powered door safety

Every powered door we fit is commissioned with force testing to BS EN 12453 and handed over with a Declaration of Conformity and UKCA or CE marking, as the Supply of Machinery (Safety) Regulations 2008 require.

Electrics

An electric door needs a power supply near the roller box. Electrical work must meet BS 7671, and in Wales some domestic electrical work is notifiable under Part P, so it is done by a registered competent person or signed off by building control.

Safety edge and photocell repairs in Port Talbot: questions

How much is a visit in Port Talbot?

Prices for safety edge and photocell repairs start from £99 inc VAT, and the price is agreed before anyone comes out. Any parts not covered by that price are quoted before they are fitted, so you can decide on the spot. The guide prices are the same in Port Talbot as elsewhere we cover.

Do you charge more for Port Talbot than other towns in West Glamorgan?

No. Guide prices are the same for Port Talbot as for anywhere else we cover in West Glamorgan. The written quote reflects your opening and the door you choose, not your postcode, apart from islands and remote areas where any travel cost is shown in advance.

Can I get a price for Port Talbot without anyone visiting?

Yes. The guide price tool takes four steps and gives a range for your opening and door type. It is a guide, not a quote: the written quote comes after the survey or once the visit price is agreed.

Can I message you a photo of my garage in Port Talbot?

Yes. Photos of the opening, the inside of the garage above the door and any existing door help us give a more useful guide price for Port Talbot. Send them by WhatsApp or mention them in your enquiry, and we will reply in writing.

How do I test my safety edge and photocells?

Follow the manufacturer's instructions for your door. In general, the test checks that the door stops or reverses when the safety edge meets an obstruction while closing, and that the door won't close while the photocell beam is broken. Keep people and pets clear while testing, and repeat the test monthly.

Why does my roller door reverse when nothing is in the way?

A door that reverses on its own while closing is often reacting to a safety device that thinks there's an obstruction. Dirty or misaligned photocells, a damaged safety edge, a loose cable or limits that have drifted can all cause it. Clean the photocell lenses and check the beam is clear, then request a visit if it continues.